Hook up doorbell transformer

Not sold on the Ring Video Doorbell 2? Here's an overview of Ring's complete DIY doorbell lineup:. Your existing drill holes might not line up with the four screws needed to mount the Video Doorbell 2. Use an electric drill to create the holes. When in doubt, hire a professional or ask an experienced friend to help.

Wiring Doorbell Transformers | Doorbells | Electrical | Repair Topics

Connect the two doorbell wires to the two screws on the back of the Video Doorbell 2. It doesn't matter which wire connects to which screw. If the wires are too short, use the wire extenders provided by Ring. Make sure they're connected and mount the doorbell using the included screws. Use wall anchors if you're installing the buzzer on brick, stucco or concrete. Attach a faceplate to complete your hardware installation. Ring includes both a satin nickel and a venetian antique bronze faceplate with your purchase.


  • marriage not dating full cast;
  • charlotte nc online dating;
  • Doorbell Wiring Diagrams.
  • How to Wire a Doorbell (with Pictures) - wikiHow.
  • Fixing Transformers.
  • dating in kolkata;

You can use them interchangeably, depending on the style you want to achieve. Go back to your breaker panel and switch power back on to your doorbell wiring. That's it -- you've just installed your Ring Video Doorbell 2. If you aren't wiring this doorbell, follow all of these steps except the ones dealing with wires. Want more information about how this doorbell compares to other smart buzzers? Be respectful, keep it civil and stay on topic. We delete comments that violate our policy , which we encourage you to read. Discussion threads can be closed at any time at our discretion.


  1. How to Check a Doorbell Transformer – Doorbell Does Not Work.
  2. dating a famous person reddit;
  3. Want FREE Home Tips & Hacks?.
  4. get me pregnant dating site;
  5. companions online dating;
  6. Don't show this again. Install the Ring Video Doorbell 2 in a flash. A simpler design helps Ring's Video Doorbell 2 shine 5 Photos.

    In other smart doorbell news The smartest video doorbell around The best video doorbells you can buy today Watch your door from afar with Ring's Video Doorbell Pro. How to install the Ring Video Doorbell 2 Sign in to comment Be respectful, keep it civil and stay on topic. Qualcomm kicks off defense in FTC trial by showing its mobile chip prowess.

    For aesthetics, you will want to run the wiring concealed, and that can be somewhat challenging.

    For the most part, run the wiring in the basement or basement crawlspace where concealment will not be a concern. Turn off the circuit breaker supplying the branch circuit where you will be connecting the transformer. The transformer may be connected using any convenient junction box that has an uninterrupted circuited passing through it. Use the noncontact voltage tester to ensure you turned off the right breaker.

    How to Hard-Wire a New Doorbell

    Mark the spot where the doorbell is to be mounted. Use the electronic stud finder to ensure you will not be drilling into a wall stud. Drill a 1-inch hole for the wires. Hold the doorbell over this hole and mark the spots where the anchoring screws are to be installed. Drill the holes for the wall anchors, using the drill bit that came with the anchor kit. Press the plastic anchors into the holes.

    Understanding Each Part of a Wired Doorbell System

    Remove the section of baseboard beneath the doorbell location. Remove a 2-inch square of the plasterboard, using the utility knife. Remove the interior trim on the latch side of the door where the button is to be installed. Cut a channel in the wallboard for the wiring. At the base of the channel, drill into the basement, using the electrician's bit. Drill another hole through the wall at the height the button is to be mounted on the outside wall. Install one length of bell wire cable from the transformer to the doorbell location. Install another length of cable from the doorbell to the door where the button will be located.

    In the basement, run these wires through holes drilled through the the floor beams or along the sides of the beams. When running the wire along the sides of the beams, secure it in place at four-foot intervals, using wire staples. Once you have all the wire in place, replace the baseboard and door trim.